ققنوس چت   زاهدان چت   
Markcoppercladsteels

Markcoppercladsteels
 
نويسندگان
آخرين مطالب
برترین مطالب
مطالب تصادفی
لینک دوستان
عضویت
نام کاربری :
پسورد :
تکرار پسورد:
ایمیل :
نام اصلی :
آمار
امروز : 1
دیروز : 0
افراد آنلاین : 1
همه : 9
پيوندهای روزانه
لينكي ثبت نشده است
چت باکس

6, Off-set :Off-set was defined as the rim engagement surface and the wheel center distance, to the lateral direction is toward the rim, inner negative. The different angle can change the tire and the ground contact point and point of force, directly affect the tire grip and wear condition.P. Below are some four wheel alignment advanced performance, perhaps in your choice to do some reference:1, no rod type measuring head ( sensor ): no rod type sensor in aerospace industry electronic inclinometer principle, as the measuring standard foundation, its advanced design, aimed at reducing the traditional long rod type measuring head for projecting need about the inconvenience and error.apoautomotive.4, do not superstition: transmission mode of vehicle four wheel alignment tester 's main function is to the chassis repair technicians to provide a set of accurate measuring data, as the adjustment of the chassis of the vehicle 's basic data, the key is provided by a sensor value is correct.I. Electronic track measuring ruler, can be adapted for use in a vehicle after the tread measurement, and through wireless transmission to the computing system data changes are made, in order to provide the most accurate measurement value. Rod type measuring head for four wheel independent measurements, so no need to worry about around the projection problem, which makes the measuring data is more accurate.2, the wireless transmission electronic track measuring ruler: the vehicle tire modified atmosphere prevails, adapted for use in a tire after two rounds between track change, but the alignmenton the original factory value did not change.Automobile suspension system mainly includes: the alignmentangle camber angle ( Camber ), ( Castor ) after the angle, beam angle ( Toe ), ( K.3, beam angle ( Toe ): defined as above about two tires the angle formed by the inward outward, Toe-in, Toe-out.When required to do car alignment1, motor vehicle inspection before2, exercise three thousand kilometers new car3, each half or the vehicles travel up to ten thousand km. While some manufacturers or stores the emphasis of so-called advanced transmission system, just after completion of measurement data as a means of transmission.4, after the dip ( Caster ): defined as a car side view of steering shaft center line and the vertical line included angle is negative, forward, backward is.5, toe-out on turns ( Toe-out on Turn ): defined as steering front wheel steering angle difference of Copper Busbar Suppliers two. Angle in vehicle suspension design of the beginning already set, is generally not adjustable. Its implications are as follows:1, camber ( Camber ): defined as a car front tire center line and the vertical line of the angles, positive negative outward, inward. Choose an advanced four wheel alignment service shop, is to do a good job in four wheel alignment precondition. After the dip of the existence of the steering axis and the road intersection in front of the tire ground, can use the road surface-to-car tire resistance to let the car straight into, the principle such as shopping cart front wheel will automatically to your force direction and keep straight into the general. ), steering angle when the first exhibition ( Toe-out on Turn ).I. With the suspension system evolution, the connecting rod is more, the structure is more complex, relative to four wheel alignment angle requirements will be getting higher and higher.com/ --  So when you choose four wheel locating stores, must remember alignmentapparatus is admittedly important, but to adjust the position and angle of "person" is more important, experience and technology and technicians with advanced automotive equipment is the best choice. Change wheel Off-set will change the car track, and the track refers to the distance between the center lines of the tire, so if only increase rims and tires without changes in Off-set, does no influence on track.P.Automotive Equipment Related Articel : When does the car do four wheel alignment How to make dynamic balance, four wheel alignment How to get a good wheel alignment Why Is Wheel Alignment So Important Does Your Car Need An AlignmentPrevious:When does the car do four wheel alignment. ): defined as steering axle center line and the vertical line of the angles. Just imagine, if the measured data are not exact, transmission data by means of advanced again have what use? So, on four wheel alignment, measuring the accuracy of the data is the most important.4, replacing and adjusting the tyre, suspension system5, replacing the steering system and components6, when the wheel is not straight7, straight line must grip the steering wheel8, straight when the vehicle is pulled toward the unilateral9, when the vehicle is steered, the steering wheel is too heavy or not automatic aligning10, exercise when feeling body sway or with a floating sensation11, tire abnormal wear12, after the car accident repairHow to choose the four wheel alignment stores?where have wheel alignment machine for saleFirst of all, to choose a good four alignment. The angle can make the weight average distribution in the bearing, protect the bearings are not easy to be damaged, and the steering force average, turning light.html ? When to do four alignment? Believe drive less friends will have such a doubt! It is carefully read the following article, small make up detailed introduction!What is four wheel alignment?The so-called four wheel alignment, refers to a later round average advance direction for alignmentreference, to the measurement and calibration of four wheel alignmentangle; so when the vehicle runs various chassis parts and tires can maintain the proper geometric relationship, so that drivers can correct, comfortable driving their love car, extend tire and chassis relevant parts of life. Turn round the bend in the rotating angle is usually larger than the curved outer, phase difference of 2 degrees, its purpose is to make the car can turn after the shaft extends line of instantaneous center of smooth curves. Beam angle of function is the compensation for camber tire and road surface resistance caused by inward or outward rolling trend, to ensure that the car straight.In addition, four wheel alignment apparatus is used to adjust, change location angle, he was used to measure the position and angle of reference for technicians, technicians to instrument measuring angle and the angle of the original factory, if exceed allowable range is adjusted or replaced part of machine parts, in order to restore design angle.com/What-is-four-wheel-alignmentwhen-they-need-to-do-4-alignment-article-190.2, angle (K.3, much angle at the same time display screen: can be a graphic data, such as color, double color display mode synchronous measurement and calibration results, convenient vehicle calibration technician.


ادامه مطلب
امتیاز:
 
بازدید:
[ ۲۲ بهمن ۱۳۹۷ ] [ ۰۹:۰۱:۳۰ ] [ markcoppercladsteels ]
[ ۱ ]
.: Weblog Themes By limoblog :.

درباره وبلاگ

آرشيو مطالب
پنل کاربری
نام کاربری :
پسورد :
لینک های تبادلی
فاقد لینک
تبادل لینک اتوماتیک
لینک :
خبرنامه
عضویت   لغو عضویت
امکانات وب